How do I save the changes I made to the labels in the onscreen PalmPad?

What do I do if the CM17A doesn't fit into my serial port?

My Firecracker® won't control the TM751 transceiver. What do I do?

When I transmit a dim command, my transceiver (TM751) dims the light all the way down and then the transceiver locks up until I unplug it. Why does this happen?

Can I use keyboard commands instead of clicking on the ON and OFF buttons?

After minimizing the User Interface, Firecracker® does not have a button on the taskbar. I try to load Firecracker® again and nothing happens. What do I do to fix this problem?

Can the Firecracker software control the CM11A ActiveHome Interface?

I wish to write my own program to control the Firecracker interface. Is there a communication protocol file available?

I own the Firecracker and ActiveHome. Can I use both on the same computer?

After I create a timer in Fuse, it doesn't execute or the next time I go back into Fuse my changes are gone. Why is this happening?

What is my Registration code for Fuse/Macro Recorder?

First, make sure that the COM Port selected in the Firecracker® software is the correct one for the serial port you have the CM17A plugged into. You can check this by right clicking on the onscreen PalmPad and selecting "Test Communications." Any COM Port displayed in gray is not available for use on your computer. You should also check in the Windows 95/98 Device Manager to make sure that the COM Port you have chosen isn't being used by another device. Bring up Device Manager by right clicking on "My Computer" from your desktop, choosing "Properties" and then the "Device Manager" tab. If you can't tell if you have selected the right COM Port, you may need to contact your computer technical support.

Once you have confirmed that the COM Ports are configured OK, you'll need to check that the CM17A can talk to the TM751. Remember, the House Code (letter dial) on the TM751 needs to be the same as the House Code in the Firecracker® software. When testing it's also helpful to plug the TM751 into an outlet in the same room as your computer. Try several times before you give up. If you still can't get it to work, call X-10 technical support at (800) 442-5138.

To help you determine if you have EMI, you will need a surge protector. If the surge protector has other devices plugged into it, remove them. The surge protector will help to create a "quiet" test area. Keep in mind, this is not an absolute method of EMI detection. Plug your transceiver and lamp module into the surge protector. Using your remote, dim the light. If the dimming problem persists, unplug/turn off any EMI producing devices, such as a cordless phone, cell phone, microwave, stereo system, computer, etc. Try dimming again.

If you are unable to determine the source of the interference, we can exchange the transceiver, provided the warranty is still valid. A replacement transceiver may be more tolerant of the EMI present in your home, however, it is likely to operate in the same manner.

1. Type the House code (A through P).

2. Type the unit code (1 through 16).

3. Type the letter N for ON and F for OFF.

To dim or brighten a lamp module:

1. Type the house code (A through P).

2. Type the unit code (1 through 16).

3. Press the + (plus) key to brighten and the - (minus) key to dim.

4. For repeated dimming or brightening of the same module, you can press + (plus) or - (minus) without entering the House or Unit code again.

To delete the last entry press the Delet or Backspace key.

To cancel the last command press the Escape key.

No. Firecracker software is designed for use with the Firecracker interface only.

Yes, the file is available on the manuals page.

Yes, provided you only work with one program at a time. It is not recommended to run both programs at the same time.

The most common cause of a Fuse timer failing to execute is due to not pressing ENTER after changing the clock in the DIGITAL display. Any changes to a timer are updated on the fly, but if ENTER is not pressed, the change to the clock is not finalized.

The best way to register your Fuse or Macro Recorder software is by using the EMAIL submission option in the splash screen. When FireCracker starts, it gives you the Macro or Fuse screen, complete with a button labeled REGISTER. When you click on this button, it gives you three ways to register: by EMAIL, FAX, and INTERNET. Select EMAIL. This form of registration is handled by the X10 R & D department, and should provide the quickest registration method possible.